Above Ground Pumping Station

Sewage pumping stations are needed when gravity cannot be relied upon to move wastewater and sewage towards the main sewer line. Perhaps there is a lack of gravitational flow if, for example, the sewage is situated below the main sewer level and would need to be pumped upwards. Maybe the sewer is obstructed by a ridge or there is no gravity system in place. In these circumstances, installing a sewage pump station could be much cheaper and just as effective as installing a sewage system with gravitational flow.

You’ll find many advantages to having a sewage pump station installed at your property. They are fitted with alarms that will notify you if there are any problems with the system. Sewage pump stations also work automatically so there is minimal human contact. This reduces the risk of health issues.

The first cost to consider is for the sewage pump station itself. And this will vary greatly depending on the specific model you chose. Whether you need a single or double sewage pump station, you’ll find our prices at Tanks Direct are extremely competitive.

Then comes the cost of installation. If you are installing a pump for the first time in a space previously unprepared for installation, the cost will be higher than if you are replacing an existing pump. This is because all the additional preparation required has already been done. The location of your install could also have a bearing on the installation cost. If the site is awkward to get to or a difficult material to dig up, your costs will be higher.

You’ll also want to consider the ongoing maintenance costs of sewage pump stations. Regular servicing is essential to keep your equipment working as well as possible. Sewage pumping stations are subject to wear and tear and require regular servicing to operate effectively. Catching any issues early will minimise the risk of failure and help prevent costly repairs.

It is vitally important that your sewage pump station is regularly serviced and properly maintained. This will improve the day-to-day efficiency of your sewage treatment pump and help improve its lifespan. By inspecting the pump regularly, you can ensure all the components are working correctly

It is advisable to get your tank serviced once a year. Your tank will be emptied and cleaned, with any blockages removed. If any defects are detected during the service, it’s best to get faulty parts

replaced as soon as possible. Failure to fix problems quickly can lead to major issues further down the line. For help and advice on how best to maintain your sewage treatment plant, please contact our friendly and knowledgeable team.

Your sewage pump should not run constantly. Usually it should run from 10 to 15 seconds until the float switch detects the water level has dropped adequately. It will then cut off. If your sewage pump is running constantly it may need to be serviced, repaired or replaced. The average life expectancy of a sewage pump is about 10 years.

In our 2” vortex range we use Hippo 50 pumps for up to 6m head and Hippo 100 pumps for up to 10m head. In our 2” macerator range we use Semison 125GR pumps, in our 2½” vortex range we use Semison 650 pumps and lastly in our 3” vortex range we use hippo 80-200. Details of which can be found either on our website or a copy can be sent across please call for more information.

You may need to service or replace your sewage pump is you find the following: -

• If the water at the discharge point is dirty or brown
• The pump is not working at all or sounds like it’s struggling to pump
• Your pump is constantly running and doesn’t switch off even though no one is using the facilities in the building
• Sewage is backed up into the building
• There is a smell of sewage
• There is no fluid emptying from the holding tank
• There is no power to the pump

If you do require a Service, please give a ring to arrange.

Yes, it is cost effective to get your sewage pump regularly maintained to lengthen the life of the pump. Typically pump servicing will include: -

• Cleaning out the sump chamber
• Cleaning of pumps and float switch
• Electrical test of pumps and all floats
• Checking all cables for damages and general wear

The size of the pump required is down to the rise to main from the tank to the sewer, please call us for further help on this.

Tanks are sized on the number of people using the system, you should allow 150 litres per person multiplied by the number of people using the property to calculate your 24hr storage capacity.

For commercial properties please contact us, and we can help size this for you. 

No the tanks are supplied without an inlet hole, this is usually drilled on site however we do supply the seal to make the hole water tight and should you require us to drill this for you at the factory, we can offer this also.

Sewage pumps are available in a few different options including effluent pumps, grinder pumps or macerator pumps and submersible pumps. Effluent pumps remove the grey wastewater that stays in your septic tank after the solids have settled and are good for residential and small commercial applications.

Grinder pumps or macerator pumps collect wastewater from your household appliances and fixtures including toilets, washing machines, and bathtubs. Grinder or macerator pumps works by the pump grinding the waste into a fine slurry before pumping it to your septic tank when the water in the tank reaches a certain level from a holding tank to collect waste. Submersible pumps are used for residential, commercial, and agricultural applications.

If you are unsure of the type of sewage pump you need, we are more than willing to help. Please give us a call or send us an email.